Problem sa LAN-om sam resio [tacnije nije ga ni bilo, moja glupost], ali i dalje ne radi wireless.
Cini se da kartica nije pravilno prepoznata i/ili inicijalizovana, uostalom evo:
Boot log
Code:
Setting up network interfaces:
lo
lo IP address: 127.0.0.1/8 done
eth0 device: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
eth0 configuration: eth-id-00:02:44:94:ec:6a
eth0 IP address: 192.168.0.1/24 done
Waiting for mandatory devices: wlan-bus-pci-0000:02:03.0
wlan-bus-pci-0000:02:03.0 No interface found failed
skippedSetting up service network . . . . . . . . . . . . . . . .failed
System log
Code:
Aug 18 16:53:40 linux kernel: acx_pci: unsupported module, tainting kernel.
Aug 18 16:53:40 linux kernel: acx100: It looks like you've been coaxed into buying a wireless network card
Aug 18 16:53:40 linux kernel: acx100: that uses the mysterious ACX100/ACX111 chip from Texas Instruments.
Aug 18 16:53:40 linux kernel: acx100: You should better have bought e.g. a PRISM(R) chipset based card,
Aug 18 16:53:40 linux kernel: acx100: since that would mean REAL vendor Linux support.
Aug 18 16:53:40 linux kernel: acx100: Given this info, it's evident that this driver is still EXPERIMENTAL,
Aug 18 16:53:40 linux kernel: acx100: thus your mileage may vary. Reading README file and/or Craig's HOWTO is
Aug 18 16:53:40 linux kernel: recommended, visit http://acx100.sf.net in case of further questions/discussion.
Aug 18 16:53:40 linux kernel: acx100: Compiled to use 32bit I/O access (faster, however I/O timing issues might occur, such as firmware upload failure!) instead of 16bit access
Aug 18 16:53:40 linux kernel: acx_init_module: dev_info is: TI acx_pci
Aug 18 16:53:40 linux kernel: acx_init_module: TI acx_pci.o: Ver 0.2.0pre8 Driver initialized, waiting for cards to probe...
Aug 18 16:53:40 linux kernel: ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 5 (level, low) -> IRQ 5
Aug 18 16:53:40 linux kernel: acx_probe_pci: WARNING: ACX111 support is quite experimental!
Aug 18 16:53:40 linux kernel: Found ACX111-based wireless network card at 0000:02:03.0, irq:5, phymem1:0xee030000, phymem2:0xee000000, mem1:0xe135c000, mem1_size:8192, mem2:0xe1400000, mem2_size:131072
Aug 18 16:53:40 linux kernel: initial debug setting is 0x001b
Aug 18 16:53:40 linux kernel: acx_select_io_register_set: using ACX111 io resource addresses (size: 56)
Aug 18 16:53:40 linux kernel: hw_unavailable = 1
Aug 18 16:53:40 linux kernel: acx_probe_pci: TI acx_pci: Using IRQ 5
Aug 18 16:53:40 linux kernel: reset hw_unavailable++
Aug 18 16:53:40 linux kernel: acx_reset_mac: enable soft reset...
Aug 18 16:53:40 linux kernel: acx_reset_mac: disable soft reset and go to init mode...
Aug 18 16:53:40 linux kernel: Attention: no custom firmware directory specified (via module parameter firmware_dir), thus using our default firmware directory /lib/firmware
Aug 18 16:53:40 linux kernel: Firmware: '/lib/firmware/TIACX111.BIN' not found. Trying alternative firmware.
Aug 18 16:53:40 linux kernel: Firmware: '/lib/firmware/FwRad16.bin' not found. Trying alternative firmware.
Aug 18 16:53:40 linux kernel: Trying to load firmware: '/lib/firmware/FW1130.BIN'
Aug 18 16:53:40 linux kernel: ERROR 2 trying to open firmware image file '/lib/firmware/FW1130.BIN': file not found - make sure this EXACT filename is in eXaCtLy this directory!
Aug 18 16:53:40 linux kernel: acx_read_fw FAILED
Aug 18 16:53:40 linux kernel: acx_reset_dev: Failed to upload firmware to the ACX1xx
Aug 18 16:53:40 linux kernel: acx_probe_pci: TI acx_pci: MAC initialize failure!
Aug 18 16:53:40 linux kernel: acx_probe_pci: TI acx_pci.o: Ver 0.2.0pre8 Loading FAILED
Aug 18 16:53:40 linux kernel: acx_pci: probe of 0000:02:03.0 failed with error -5
Sta mi predlazete?
P.S.Sorry zbog velikog log-a
"None may challenge the Brotherhood!"
Edwin VanCleef <Defias Kingpin>